HU - Budapest: Electrical installations for railways

- Budapest, Hungary, Europe

Section II: Object

II.1)Scope of the procurement


TATRA T5C5 for hammers

Reference number: EKR000436452018
II.1.2)Main CPV code
II.1.3)Type of contract
II.1.4)Short description:

BKV Vasúti Járműjavító Kft. To modernize the existing T5C5 electric vehicles

Part 1: Purchase of hacking equipment and vehicle control unit and other electrical equipment related to drive chains (6 types)

Part 2: Acquisition of Power Transducer and Fan (2)

Part 3: Procuring a Transmitter (1)

Purchase in accordance with the technical specifications detailed in the Procurement Document.

The name, brand name, etc. in the technical description may be mentioned. in order to clearly define the nature of the product, as set out in 321/2015. (3), the contracting authority accepts the equivalent quality product.

II.1.5)Estimated total value
Value excluding VAT: 1.00 HUF
II.1.6)Information about lots
This contract is divided into lots: yes
Tenders may be submitted for all lots



Hinging equipment and vehicle control unit

Lot No: 1
II.2.2)Additional CPV code(s)
II.2.3)Place of performance
NUTS code: HU110
Main site or place of performance:

1106 Budapest, Fehér út 1 / b. (seat of the contracting entity)

II.2.4)Description of the procurement:

A chopper device and the vehicle control unit and the acquisition of other electrical devices associated driveline (6 & apos;): 18 sets

Under 1 set, the contracting authority understands the amount needed to modernize a piece of vehicle.

The contracting authority draws attention to the fact that, in the present offer, the T5C5 electric vehicles are required to obtain a chipping device and a vehicle control unit with the parameters specified below with the exception that the above-mentioned, equivalent, interchangeable product contracting entity accepts:

Vehicle Control Unit: Vehicle Control Unit for T5C5K2 Electric Vehicle VVE-06, or equivalent (hereinafter referred to as VAE), interchangeable with the existing 180-piece T5C5K2 fleet vehicle control unit

Vehicle Controller consists of the following units:

- Main Control Rack (VVE-06)

1. Input Card 1 (2 DIC-1 Cards VAE)

a) Provides 24 optically isolated inputs.

b) system bus alignment with other cards.

2. Relay output card (2 DRV cards VAE)

a) 14 independent output relay contact cards.

3. Transmission Card 1 SCI-4 Card - FLS-1 Memory Module or equivalent)

a) Measures the speed of the vehicle by converting the pulse signals of the speed encoder mounted on the motors to an analog signal proportional to the rotation.

b) The PWM digital setpoint is converted to 0 to + 5V analogue signal.

4. Input Card 3 (1 MV-4 Card VAE)

a) 4 comparator inputs, 2 optical inputs, logic control, 2 relay and 2 optical outputs for error indication.

5. Analog Input Card (1 AIO-5 Card VAE)

a) An 8-channel analog input,

b) sample hold unit with analogue multiplexer and 12 bit AD converter,

c) comparator output,

d) VFC input,

e) Analog output with 12-bit DA converter,

f) contains a reference voltage output.

6. Light Cables Card (1 OPI-1 Card VAE)

a) Transforms TTL-level logic signals into a light-wired transmitted signal, containing 4 transmitters and 4 receivers.

7. Micro controller board (1 PCM-3 or PCM-4 card VAE), include:

a) The system's central unit card. Key elements:

b) Motorola MC68376 microcontroller (32-bit core, 16-bit external bus,

c) integrated peripherals, CPU clock frequency: 20MHz),

d) 512 static RAM,

e) 2 Mbájt Flash memory,

f) 8 kb SPI bus EEPROM,

g) Monitoring circuit type MAX693A,

h) real-time (real time) DS1302 battery charging control,

i) Intel 82527 CAN 2.0B Controller,

j) Galvanically isolated RS232 serial line,

k) 2 galvanically isolated (1Mbps) CAN lines,

l) 2 analog inputs (0-5V) from the rear panel,

m) voltage reference and temperature measurement using the LT1019 circuit,

8. Serial Bus Card (1 SRO Card VAE)

a) bus coupling,

b) line line handling (RS485, RS232),

c) real-time clock circuit,

d) contain non-volatile memory

9. Memory card (1 FLS-1 card VAE)

a) The card is a serial module memory module (SCI-4 module). The card is made up of non-volatile FLASH EPROM circuits, which will retain its contents even if there is no power supply.

10. Power supply (1 K300S-2 power supply VAE)

a) Provides adequate power supply for the cards

- Power supply rack (1 VVT-06 power supply rack VAE)

1. Power supply (1 X200-S2 power supply VAE)

2. Power Supply Control Card (1 VMT-06 VAE)

3. Battery Management Card (1 AKU-03 Card VAE)

The unit provides power to the control compartment for short-time power failure or voltage reduction. The unit should include a battery of at least 18V 1.2Ah gel.

The vehicle controller should include cooling fans, heat exchangers, and adequate airflow fans (12x12cm), which can be used when the vehicle controller is operating at operating temperature. The vehicle controller must have a piece of ambient temperature sensor which , when reaching +3 ° C, switch on the cooling fan of the vehicle control unit.

Continued Section VI.4.3

II.2.5)Award criteria
Criteria below
II.2.6)Estimated value
Value excluding VAT: 1.00 HUF
II.2.7)Duration of the contract, framework agreement or dynamic purchasing system
Duration in months: 12
This contract is subject to renewal: no
II.2.10)Information about variants
Variants will be accepted: no
II.2.11)Information about options
Options: no
II.2.12)Information about electronic catalogues
II.2.13)Information about European Union funds
The procurement is related to a project and/or programme financed by European Union funds: no
II.2.14)Additional information

1) Section II.2.6 was completed for the purpose of transmitting the notice.

2) The 18 sets (with a total of 6 types of products) will be awarded by contracting calls, which must be awarded to the winning bidder within 120 days after the withdrawal of the call.

Click for more info
Contracting authority
BKV Vasúti Járműjavító Szolgáltató Korlátolt Felelősségű Társaság
Budapest, Hungary, Europe
Time-limit for receipt of tenders or requests to participate
Friday, October 12, 2018 12:00 AM
Language(s) in which tenders or requests to participate may be drawn up
  • Join our community for FREE today!

  • Create and share your own profile

  • Join the discussions

  • Publish your own items

  • Subscription to our Weekly eNewsletter

your benefits?

Get connected with Mass Transit Professionals Worldwide

Create your account

Sign in with LinkedIn Close

FREE membership benefits

  • * create and share your own profile
  • * join the discussions
  • * publish your own items on Mass Transit Networkmanage news, jobs, tenders, companies, events, showcases, educations, associations and literature.
  • * subscribe to our weekly eNewsletter